Hyundai Getz 5 Doors 2002 Reviews - 2005

Hyundai Getz 5 doors 2002 - 2005 collected from masters and engineers of service stations for an objective assessment of reliability and features of the GETZ 5 doors.
Engine It is often happening to flow the valve cover (engine 1.3). The lamb-probe fault is a weak place of the model, can lead to the failure of the neutralizer. Cooling radiator quickly breaks.
Transmission minimum Repair Cost Problems
Control system and suspension The resource of the rear shock absorbers is not more than 40 thousand km (rear shock absorber - 1,552 rubles; work is 1 norm-hour).
Brake system minimum Repair Cost Problems
Heated air and air conditioning minimum Repair Cost Problems
Start and Charging System minimum Repair Cost Problems
Electrical components and other minimum Repair Cost Problems
Body stability to corrosion Corrosion begins with the lower edges of the doors and the lid of the trunk.
* Information collected from specialists from service stations
Minimum Repair Cost Problems
Medium problems
Serious problems with high repair cost

your comment

your name:
your comment:
uRAL.
2012-06-28 10:28:01

nE Krutite Oborota Svishe 2,5K Na Geshke I Skorost 'Ne Bolshe 130 Pri Etom - Dal'she Tolko Neopravdannij Rashot Topliva

To answer
-1
Dima
2012-07-12 17:56:25

i have a mileage of 39 thousand and now the fourth morning in a row in the cold jump turns up to 2000 and so 2-3 times during the launch. Further everything is fine. It is only in the morning. What is it?

To answer
0
Sergey
2012-07-12 18:05:55

So it can be just a warm-up mode: on some machines it is so, when the turnover is reproduced immediately, then as it is warm up. Can bounce several times and descend.

To answer
0
Bibwardia
2012-07-13 09:36:05

We recommend checking the idling regulator and the mass flow sensor.

To answer
0
Dmitriy
2012-08-01 00:53:41

Guys, I also squeezed some error ((\u003cbr/\u003e Help it get rid of it !!! \u003cbr/\u003e In general, I have a constantly beginning to light up the ABS lamp and a manual brake lamp. And not immediately after you get started, Some time: From half a minute to 10 minutes, it may not be lit, and then two light bulbs light up and without any patterns and only off / incl. ignition. And also when the lights are burning ABS does not work! !! Wheels are blocked when the brake is pressed, and the car begins to go through. The fuses are all whole, the brakesuha at the maximum. Multitroniks CL-550 bortovik does not show errors. Clem with the battery has already discarded - without a result ... I don't know what to sin BR /\u003e Advise something! \u003cbr/\u003e \u003cbr/\u003e PS without ABS very, very bad.

To answer
0
Shplling
2012-08-01 02:16:28

Taks to the computer need to be connected: it will show the error, most likely one of the ABS sensors in the process of failure ... either contact with him leaves. Here the first thing is the computer, the main thing is to understand what kind of sensor is buggy, then the contact of it with the woven, it may well be the case in this contact. Contact, in the sense of the connector on the hub through which it is connected.

To answer
0
Vladimir
2012-12-07 00:32:18

hello, I caught fire ABS lamp and slows down the right rear wheel what to do

To answer
0
Dimka
2012-12-07 01:10:29

Most likely the case in the brake preport (cause of braking), you need to remove the wheel, clean and lubricate the caliper ... possibly because of this and the lamp is lit

To answer
0
Fedor.
2012-12-07 01:19:45

Yes, everything is true, jammed the caliper, it needs to be cleared and smeared

To answer
0
Rer.
2012-08-20 19:47:33

I have a 1.3 engine, mileage 227 thousand km. Requires Cap repair or engine replacement, is it normal?

To answer
1
Paltos
2012-09-04 10:31:23

Probably the result of an untimely

To answer
-1
Volgograd
2012-09-27 17:50:57

Guys, help! Something at speed the car began to throw from side to side! Help where to watch and dig?

To answer
0
BibIedchik
2012-09-27 17:54:51

1) Check that nuts are well spinning in wheels \u003cbr/\u003e 2) It is possible to the inside of the discs and stuck. You need to look thoroughly and if it is, it is clean. \u003cbr/\u003e 3) If it's not in paragraph 1 and 2, then the wheel balancing is most likely.

To answer
-1
Volgograd
2012-09-27 17:57:03

Wow! Thank you for super operational response. I went to look

To answer
0
Volgograd
2012-10-02 16:22:58

Yes, on the inside of the disk there was a dirt that created vibration. Thanks again

To answer
0
Alexey
2014-08-20 17:51:17

motor 1.3 Whether the valve oppresses the timing belt

To answer
0
basil
2014-11-17 14:56:19

in my opinion, on all engines at the getters of the grommet when the timing break

To answer
1
basil
2014-11-17 14:54:56

tell me, whether there are cars without an amplifier steering

To answer
2